CISCO-MGX82XX-DSX3-MIB Download

cwDsx3ConfigTable

The DS3/E3 Configuration table. There is one row for each DSX3 port in the system. The table size (number of rows) is given by the value of dsx3LineNumOfValidEntries.

cwDsx3ConfigEntry

An entry in the DSX3 Configuration table.

dsx3LineNum

This object is the identifier of a DS3/E3 Interface on a managed device. The range supported depends upon the type of the card(controller card, service module). For 1 port Card : Range is 1..1 Example : CESM-T3E3 For 2 Port Card : Range is 1..2 Example ...

cwDsx3LineType

This variable indicates the variety of DS3 C-bit or E3 application implementing this interface. The type of interface affects the interpretation of the usage and error statistics. The rate of DS3 is 44.736 Mbps and E3 is 34.368 Mbps. The values, in sequen ...

cwDsx3LineCoding

This variable describes the variety of Zero Code Suppression used on this interface, which in turn affects a number of its characteristics. dsx3B3ZS and e3HDB3 refer to the use of specified patterns of normal bits and bipolar violations which are used to ...

cwDsx3LineLength

This object specifies the length of the DS3 Line. This object provides information for line build out circuitry if it exists and can use this object to adjust the line build out.

dsx3LineOOFCriteria

This object specifies the out of frame decision criteria. OOF is declared when errors are detected in the framing octets for four consecuitive frames. fBits3Of8(1) : an OOF condition is declared if at least 3 of 8 framing bits are in error. fBits3Of16(2) ...

dsx3LineAIScBitsCheck

If check C-Bits options is chosen then AIS is declared when 1010 pattern is found and C-Bits are all zero. In the other case an AIS condition is declared when the AIS pattern 1010... is detected irrespective of the state of the C Bits. This object does no ...

dsx3LineLoopbackCommand

This variable represents the loopback configuration of the DS3/E3 interface. The values mean: dsx3NoLoop Not in the loopback state. A device that is not capable of performing a loopback on the interface shall always return this as it's value. dsx3RemoteL ...

dsx3LineRcvFEACValidation

This entry specifies the FEAC code validation criteria. fFEACCodes4Of5(1) : a valid FEAC code is declared if 4 of 5 codes match. fFEACCodes8Of10(2): a valid FEAC code is declared if 8 of 10 codes match. fFEACCodesDisable(3) : Do not respond to any valid F ...

dsx3LineXmtFEACCode

This variable indicates what bit-oriented code to transmit over the far-end alarm and control (FEAC) channel. The values mean: dsx3SendNoCode sending looped or normal data dsx3SendLineCode sending a request for a line loopback dsx3SendPayloadCode sending ...

dsx3LineBERTEnable

This object enables/disables the BERT function on an interface. The possible values are : disabled(1): disables port BERT functionality enabled (2): enables port BERT functionality. value specified in dsx3LineBERTPattern is transmitted over the interface. ...

dsx3LineBERTPattern

This object defines the test bit pattern to be used for BERT. The possible values are : Repetitive Patterns allZero(1): All Zeroes(Continuous spaces). This is repeating pattern of zeros(...000...). The use of this pattern is to test and verify that the o ...

dsx3LineBERTResult

Result of BERT Test. The value in this object is not applicable if dsx3LineBERTEnable is set to disabled(1).

dsx3BERTResultClrButton

Setting this object to clear(2) causes the BERT result field to get cleared.

dsx3TrailTraceOption

This object is used for enabling/disabling G.832 Trail Trace. The trail trace is used to repetitively transmit a trail access point identifier so that a trail receiving terminal can verify its continued connection to the intended transmitter. It uses a 16 ...

dsx3TxTrailTrace

This object is used for specifying the data to be used for G.832 Trail Trace ID/String. This object is applicable only for E3 interfaces with G.832 framing. The trail trace ID is a 16 octet field that contains 1 octet of CRC-7(first octet) and 15 octets o ...

dsx3RxTrailTrace

Received G.832 Trail Trace string. The format of the value is: First byte indicates CRC-7(frame start marker). Bytes 2-6 (ASCII) [Byte 1-5 of this object] Bytes 7-11 (ASCII) [Byte 6-10 of this object] Bytes 12-16 (ASCII) [Byte 11-15 of this object] The ...

dsx3TxTimingMarker

Transmitted timing marker bit in G.832 MA byte. This object can be set to traceable(1) to indicate that the timing source is traceable to a primary reference clock and is otherwise set to untraceable(2). This is always set to untraceable(2) in case of car ...

dsx3RxTimingMarker

Received timing marker bit in G.832 MA byte. This object can be set to traceable(1) to indicate that the timing source is tracable to a primary reference clock and is otherwise set to untraceable(2). This is always set to untraceable(2) in case of card wh ...

dsx3TxPayloadType

This object specifies the G.832 payload type for transmit data. The possible values are : unequipped (1): not carrying any payload equipped (2): Equipped,non-specific atm (3): ATM sdhtu12s (4): SDH Elements mapping It is recommended that this o ...

dsx3RxPayloadType

Received payload type field in G.832 byte The possible values are : unequipped (1): not carrying any payload equipped (2): Equipped,non-specific atm (3): ATM sdhtu12s (4): SDH Elements mapping It is recommended that this object is not instantia ...

dsx3TxTumf

This object contains the value of Tributary Multiframe Indicator(bits 6 and 7 of MA byte) in case of TU-1xs mapping. This is not supported in FRSM-VHS and CESM-T3/E3.

dsx3RxTumf

This object contains the value of Tributary Multiframe Indicator(bits 6 and 7 of MA byte) in case of TU-1xs mapping. This object is not supported in FRSM-VHS and CESM-T3/E3.

dsx3LineEnable

This object is used for enabling/disabling an interface and modifying the interface configuration. The possible values are: disable (1): Interface is administratively down enable (2): Interface is administratively up. modify (3): Used for modifying the ...

dsx3FarEndLoopbkLineNum

Specify which DS1 or DS3 line in the far-end for the loopback testing. For CESM-T3/E3, only ds3line(30) is valid.

dsx3LineXmtClockSrc

The source of the transmit clock. backplaneClk(2) : clock source is from the backplane. recoverClk (3) : clock source is derived from another t3 interface. localClk (4) : clock source is from a local oscillator on the card

dsx3FarEndLoopbkLineStatus

This is a bitmap of the DSX3 FarEnd line loopback status bits Bit Position Loopback indicator ----------- ----- 1 DS1 Line 1 2 DS1 Line 2 3 DS1 Line 3 4 DS1 Line 4 5 DS1 Line 5 6 ...

dsx3LineEqualizer

This object indicates whether the internal equalizer is being used or bypassed. Set this value depending on the line equipment to which the receiver is attached. intrnlequalizer(1): Use internal line equalizer extequalizer(2) : Use External equalizer or ...

dsx3NearEndLoopbkLineStatus

This is a bitmap of the DSX3 NearEnd line loopback status bits BitPosition Loopback indicator ----------- ----- 1 DS1 Line 1 2 DS1 Line 2 3 DS1 Line 3 4 DS1 Line 4 5 DS1 Line 5 6 ...

dsx3SubRateEnable

This variable controls whether the DS3 subrates are enabled or not. The DS3 subrate is part of DSU functionality. This object is currently supported only in FRSM-VHS cards. It is recommended that this object is not instantiated in case of cards which does ...

dsx3DsuSelect

The dsx3DsuSelect variable controls the type of DSU mode to be selected. The 'dsx3SubRateEnable' has to be set to 'enable' before selecting the mode in 'dsx3DsuSelect'. The possible values for this are : dl3100Mode - Indicates compatibility with Digit ...

dsx3LineRate

The desired line rate when 'dsx3SubRateEnable' is enabled. If dsx3DsuSelect is set to 'dl3100Mode', the line rate can be configured in steps of 300 Kbps. If dsx3DsuSelect is set to 'adcKentroxMode', the line rate can be configured in steps of 500 Kbps. T ...

dsx3LineScrambleEnable

This variable turns the scrambling feature ON/OFF The scrambling is a technique that enables framing to be maintained on certain medium-speed edge and trunk interfaces. This object is ONLY applicable for FRSM-2T3/E3.

dsx3LineNumOfValidEntries

The number of DSX3 configuration entries (regardless of their current configuration) in the cwDsx3ConfigTable.

dsx3AlarmConfigTable

The DSX3 interface alarm configuration table. This table contains the parameters associated with detecting and declaring alarms for the interface. The parameters include severity of alarm, alarm integration parameters and 15 minute and 24 hour thresholds. ...

dsx3AlarmConfigEntry

An entry in the DSX3 Alarm Configuration table. Thresholds may be configured for: Line Code Violations (LCV), LineErrored Seconds (LES), Line Severely Errored Seconds (LSES), P-bit Coding Violations (PCV), P-bit Errored Seconds ...

dsx3RedSeverity

This variable is used to setup the severity of RED alarm. So when LOS/LOF alarm is detected the card will send the alarm with appropriate severity status. A major alarm will cause audible notification and the MAJOR ALARM LED will be turned ON. A minor ala ...

dsx3NEAlarmDownCount

This parameter specifies the decrement to the Near End alarm integration counters. The local alarms are LOS and LOF. The Default value is 1 and the integration counter is decremented by this value every 10 ms while no alarm persists. The counter is increm ...

dsx3NEAlarmThreshold

The value set in this object determines the value that the alarm integration counter must reach for an near end Alarm to be declared. If the up count is 6, the down count is 1 and the threshold 1500, an Alarm is integrated in 2.5 sec and removed in 15 sec ...

dsx3FEAlarmUpCount

This parameter specifies the increment to the Far End alarm integration counters. The local alarms are RAI and AIS. The Default value is 6 and the integration counter is incremented by this value every 10 ms while the alarm persists. The counter is decrem ...

dsx3FEAlarmDownCount

This parameter specifies the decrement to the Far End alarm integration counters. The local alarms are AIS and RAI. The Default value is 1. The integration counter is decremented by this value every 10 ms (till zero), while no alarm persists. The counter ...

dsx3FEAlarmThreshold

The value set in this object determines the value that the alarm integration counter must reach for an far end Alarm to be declared. If the up count is 6, the down count is 1 and the threshold 1500, an Alarm is integrated in 2.5 sec and removed in 15 seco ...

dsx3StatisticalAlarmSeverity

This variable is used to setup the severity of any of the Statistical alarms. So when a Statistical Counter exceeds its specified threshold the card will send the alarm with appropriate severity. A major alarm will cause the audible notification and the M ...

dsx3LCV15MinThreshold

The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.

dsx3LCV24HrThreshold

The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval

dsx3LES15MinThreshold

The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.

dsx3LES24HrThreshold

The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval

dsx3LSES15MinThreshold

The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.

dsx3LSES24HrThreshold

The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval

dsx3PCV15MinThreshold

The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not supported in CESM-T3/E3. This object is not applicable for E3 interface.

dsx3PCV24HrThreshold

The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval This object is not supported in CESM- ...

dsx3PES15MinThreshold

The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not supported in CESM-T3/E3. This object is not applicable for E3 interface.

dsx3PES24HrThreshold

The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval. This object is not supported in CESM ...

dsx3PSES15MinThreshold

The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object does not apply to the E3 interface. This object is not supported in CESM-T3/E3.

dsx3PSES24HrThreshold

The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval. This object is not applicable for E3 ...

dsx3SEFS15MinThreshold

The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not supported in CESM-T3/E3

dsx3SEFS24HrThreshold

The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval. This object is not supported in CESM ...

dsx3AISS15MinThreshold

The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not supported in CESM-T3/E3

dsx3AISS24HrThreshold

The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval This object is not supported in CESM- ...

dsx3UAS15MinThreshold

The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.

dsx3UAS24HrThreshold

The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval

dsx3E3BIP8CV15MinThreshold

G.832 BIP-8 error monitoring byte. 15 minute threshold value. This has no significance to E3 with G.751 framing which is used in FRSM-VHS This object is not supported in CESM-T3/E3.

dsx3E3BIP8CV24HrThreshold

G.832 BIP-8 error monitoring byte. 24 hour threshold value. This has no significance to E3 with G.751 framing which is used in FRSM-VHS. This object is not supported in CESM-T3/E3.

dsx3E3BIP8ES15MinThreshold

G.832 BIP-8 error monitoring byte. 15 minute threshold value. This has no significance to E3 with G.751 framing which is used in FRSM-VHS. This object is not supported in CESM-T3/E3.

dsx3E3BIP8ES24HrThreshold

G.832 BIP-8 error monitoring byte. 24 hour threshold value. This has no significance to E3 with G.751 framing which is used in FRSM-VHS This object is not supported in CESM-T3/E3 ::= { dsx3AlarmConfigEntry 31 } SYNTAX Integer32 (0..2147483647) MAX-ACC ...

dsx3CCV24HrThreshold

The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval This object is not applicable for E3 ...

dsx3CES15MinThreshold

The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not applicable for E3 interface. This object is not supported in CESM-T3/E3.

dsx3CES24HrThreshold

The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. This object is not applicable for E3 interface. This object is not supported in CESM-T3/E3.

dsx3CSES15MinThreshold

The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared. This object is not applicable for E3 interface. This object is not supported in CESM-T3/E3.

dsx3CSES24HrThreshold

The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. This object is not applicable for E3 interface. This object is not supported in CESM-T3/E3.

dsx3AlarmTable

The DSX3 interface alarm table. This table contains the performance statistics and Error Events based on 15 minute and/or 24 hour interval. Performance Parameters: LES : Line Errored Seconds PES : P-bit Errored Seconds PSES : P-bit Severely Errored Seco ...

dsx3AlarmEntry

An entry in the DSX3 Alarm table. The bucket statistics(15 minute and 24 hour interval statistics) are gathered for each ds3/e3 interface. Any entry is created automatically when ds3 interface is created.

dsx3LineAlarmState

This variable is a bitmap of the DSX3 Line ALarms on the card. A value of zero indicates no alarms. Itemized below are the individual bits: BitPosition Alarm ----------- ----- 0 Receiving RAI 1 Transmitting RAI 2 ...

dsx3LCV15MinBucket

The number of Line Code Violations(LCV) encountered by the interface in current last 15 minute period.

dsx3LCV24HrBucket

The number of Line Code Violations(LCV) encountered by the interface in current last 24 hour period.

dsx3LESCurrent

The number of Line Errored Seconds(LES) encountered by the interface in current 15 minute period.

dsx3LES15MinBucket

The number of Line Errored Seconds(LES) encountered by the interface in last 15 minute period.

dsx3LES24HrBucket

The number of Line Errored Seconds(LES) encountered by the interface in last 24 hour period.

dsx3LSESCurrent

The number of Line Severely Errored Seconds(LSES) encountered by the interface in current 15 minute period.

dsx3LSES15MinBucket

The number of Line Severely Errored Seconds(LSES) encountered by the interface in last 15 minute period.

dsx3LSES24HrBucket

The number of Line Severely Errored Seconds(LSES) encountered by the interface in last 24 hour period.

dsx3PCVCurrent

The number of P-bit Coding Violations(PCV) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3

dsx3PCV15MinBucket

The number of P-bit Coding Violations(PCV) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3

dsx3PCV24HrBucket

The number of P-bit Coding Violations(PCV) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3

dsx3PESCurrent

The number of P-bit Errored Seconds(PES) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3

dsx3PES15MinBucket

The number of P-bit Errored Seconds(PES) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3

dsx3PES24HrBucket

The number of P-bit Errored Seconds(PES) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3

dsx3PSESCurrent

The number of P-bit Severely Errored Seconds(PSES) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3

dsx3PSES15MinBucket

The number of P-bit Severely Errored Seconds(PSES) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3

dsx3PSES24HrBucket

The number of P-bit Severely Errored Seconds(PSES) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3

dsx3SEFSCurrent

The number of Severely Errored Framing Seconds(PSES) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3

dsx3SEFS15MinBucket

The number of Severely Errored Framing Seconds(PSES) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3

dsx3SEFS24HrBucket

The number of Severely Errored Framing Seconds(PSES) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3

dsx3AISSCurrent

The number of AIS Severely Errored Seconds encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3

dsx3AISS15MinBucket

The number of AIS Severely Errored Seconds encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3

dsx3AISS24HrBucket

The number of AIS Severely Errored Seconds encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3

dsx3UASCurrent

The number of Unavailable Seconds(UAS) encountered by the interface in current 15 minute period.

dsx3UAS15MinBucket

The number of Unavailable Seconds(UAS) encountered by the interface in last 15 minute period.

dsx3UAS24HrBucket

The number of Unavailable Seconds(UAS) encountered by the interface in last 24 Hour period.

dsx3PercentLcvEFS

This object gives the percentage of seconds without any LCV Errors in the total elapsed seconds.

dsx3E3BIP8CVCurrent

The number of G.832 BIP-8 Coding Violations (CV) encountered by the interface in current 15 minute period. This object is not supported in FRSM-VHS and CESM-T3/E3

dsx3E3BIP8CV15MinBucket

The number of G.832 BIP-8 Coding Violations (CV) encountered by the interface in last 15 minute period. This object is not supported in FRSM-VHS and CESM-T3/E3

dsx3E3BIP8CV24HrBucket

The number of G.832 BIP-8 Coding Violations (CV) encountered by the interface in last 24 Hour period. This object is not supported in FRSM-VHS and CESM-T3/E3

dsx3E3BIP8ESCurrent

The number of G.832 BIP-8 Errored Seconds(ES) encountered by the interface in current 15 minute period. This object is not supported in FRSM-VHS and CESM-T3/E3

dsx3E3BIP8ES15MinBucket

The number of G.832 BIP-8 Errored Seconds(ES) encountered by the interface in last 15 minute period. This object is not supported in FRSM-VHS and CESM-T3/E3

dsx3E3BIP8ES24HrBucket

The number of G.832 BIP-8 Errored Seconds(ES) encountered by the interface in last 24 Hour period. This object is not supported in FRSM-VHS and CESM-T3/E3

dsx3E3BIP8SESCurrent

The number of G.832 BIP-8 Severely Errored Seconds(SES) encountered by the interface in current 15 minute period. This object is not supported in FRSM-VHS and CESM-T3/E3

dsx3E3BIP8SES15MinBucket

The number of G.832 BIP-8 Severely Errored Seconds(SES) encountered by the interface in last 15 minute period. This object is not supported in FRSM-VHS and CESM-T3/E3

dsx3E3BIP8SES24HrBucket

The number of G.832 BIP-8 Severely Errored Seconds(SES) encountered by the interface in last 24 Hour period. This object is not supported in FRSM-VHS and CESM-T3/E3

dsx3LineAlarmClrButton

Setting this object to dsx3LineAlarmClear will cause all the alarms statuses and counters to reset.

dsx3CCVCurrent

The number of C-bit Coding Violations(CCV) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3

dsx3CCV15MinBucket

The number of C-bit Coding Violations(CCV) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3

dsx3CCV24HrBucket

The number of C-bit Coding Violations(CCV) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3

dsx3CESCurrent

The number of C-bit Errored Seconds(CES) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3

dsx3CES15MinBucket

The number of C-bit Errored Seconds(CES) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3

dsx3CES24HrBucket

The number of C-bit Errored Seconds(CES) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3

dsx3CSESCurrent

The number of C-bit Severely Errored Seconds(CSES) encountered by the interface in current 15 minute period. This object is not supported in CESM-T3/E3

dsx3CSES15MinBucket

The number of C-bit Severely Errored Seconds(CSES) encountered by the interface in last 15 minute period. This object is not supported in CESM-T3/E3

dsx3CSES24HrBucket

The number of C-bit Severely Errored Seconds(CSES) encountered by the interface in last 24 Hour period. This object is not supported in CESM-T3/E3

dsx3CounterTable

This table is for ds3/e3 statistics. This table maintains the number of times the line encountered LOS, LOF, AIS, RAI, CCV and Framing Errors(FE) from the time it is up. Error statistics are cleared when the line is brought up from the failure state.

dsx3CounterEntry

An entry in the table. Statistics are gathered for each ds3/e3 interface. An entry is created automatically for each ds3/e3 interface that is activated.

dsx3RcvLOSCount

The number of times the Loss of Signal was detected with or without integrating to LOS alarm.

dsx3RcvOOFCount

The number of times the Out of Frame was detected with or without integrating to OOF alarm. This object is not supported in CESM-T3/E3

dsx3RAICount

The number of times Yellow Alarms was detected with or without integrating to RAI alarm. This object is not supported in CESM-T3/E3

dsx3CCVCount

The counter associated with the number of C Bit Coding Violations encountered by a DS3/E3 interface. This object is not supported in CESM-T3/E3

dsx3FECount

The number of Framing Pattern Errors encountered by a DS3/E3 interface. This object is not supported in CESM-T3/E3

dsx3AtmHECCount

The number of Header Check Sequence(HCS) Errors. This object is not supported in CESM-T3/E3

dsx3AtmHECSecCount

The number of HEC errored seconds. This object is not supported in CESM-T3/E3

dsx3AtmSEHECSecCount

The number of Severely HEC error seconds. This object is not supported in CESM-T3/E3

dsx3CounterClrButton

This variable is used to clear all the counters.

dsx3RcvPERRCounter

The number of P-bit parity error. This object is not supported in CESM-T3/E3

dsx3RcvFEBECounter

The number of Far-end block error. This object is not supported in CESM-T3/E3

dsx3RcvEXZCounter

The number of excessive zeros This object is not supported in CESM-T3/E3

dsx3LCVCount

The counter associated with the number of Line Coding Violations encountered by a DS3/E3 interface.

dsx3PlcpConfigTable

This table contains ATM interface DS3 PLCP configuration parameters.

dsx3PlcpConfigEntry

An entry in the DSX3 PLCP Configuration table.

dsx3PlcpNum

This object identifies the dsx3 PLCP interface. The value of this object must be same as the value specified in 'dsx3LineNum' object from cwDsx3ConfigTable.

dsx3PlcpCellFraming

The value for this object sets the cell delineation method used by the interface. The cell delineation defines how a receiving device recognizes the start and end of an ATM cell. framingByPlcp (1): The ATM Cells are in predetermined location within each ...

dsx3PlcpLoopCommand

specifies the type of loopback on the line. The possible value(s) are : noLoop (1): Not in loopback. remoteLineLoop (2): Remote Line Loopback. localLineLoop (3): Local Line Loopback.

dsx3PlcpNumOfValidEntries

This variable indicates the maximum number of entries in cwDsx3ConfigTable.

dsx3PlcpAlarmConfigTable

This table contains the ATM interface PLCP alarm parameters.

dsx3PlcpAlarmConfigEntry

An entry in the DSX3 PLCP Alarm Configuration table. Thresholds may be configured for: Errored Seconds (ES) Coding Violations (CV) Severely Errored Seconds (SES) Unavailable Seconds (UAS), Once these thresholds are exceeded, minor ...

dsx3PlcpRedSeverity

This variable is used to setup the severity of PLCP RED alarm. So when PLCP_OOF alarm is detected the card will declare the alarm with appropriate severity status. A major alarm will cause the audible notification and the MAJOR ALARM LED will be turned ON ...

dsx3PlcpRAISeverity

This variable is used to setup the severity of PLCP RAI alarm. So when PLCP RAI alarm is detected the card will send the alarm with appropriate severity status. A major alarm will cause the audible notification and the MAJOR ALARM LED will be turned ON. A ...

dsx3PlcpLssSeverity

This variable is used to setup the severity of PLCP RAI alarm. So when PLCP LSS alarm is detected the card will send the alarm with appropriate severity status. A major alarm will cause the audible notification and the MAJOR ALARM LED will be turned ON. A ...

dsx3PlcpLssEnable

This objects specifies whether the LSS feature is enabled/disabled.

dsx3PlcpLssCodeConnected

This object derfines the value of the LSS code that is to be interpreted as Link Connected.

dsx3PlcpLssCodeRxLinkDn

This object defines the value of the LSS code that is to be identified as Receive Link Down.

dsx3PlcpLssCodeRxLinkUp

This object defines the value of the LSS code that is to be interpreted as Receive Link Up.

dsx3PlcpStatisticalAlarmSeverity

This variable sets up the severity of PLCP Statistical alarm. So when PLCP Statistical alarm is detected, the card will send the alarm with appropriate severity. A major alarm will cause the audible notification and the MAJOR ALARM LED will be turned ON. ...

dsx3PlcpBip8CV24HrThreshold

The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval

dsx3PlcpBip8ES15MinThreshold

The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.

dsx3PlcpBip8ES24HrThreshold

The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval

dsx3PlcpBip8SES15MinThreshold

The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.

dsx3PlcpBip8SES24HrThreshold

The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval

dsx3PlcpSEFS15MinThreshold

The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.

dsx3PlcpSEFS24HrThreshold

The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval

dsx3PlcpUAS15MinThreshold

The value set in this object determines the value which when exceeded in a 15 minute window causes a statistical alarm to be declared.

dsx3PlcpUAS24HrThreshold

The value set in this object determines the value which when exceeded in a sliding 24 hour window causes a statistical alarm to be declared. The threshold is checked every 15 minutes for the preceding 24 hour interval

dsx3PlcpAlarmTable

This table contains ATM interface DS3 PLCP alarm configuration.

dsx3PlcpAlarmEntry

An entry in the ATM DS3 PLCP alarm table. Bucket statistics (15 minute and 24 Hour interval) are gathered for each ds3/e3 interface automatically.

dsx3PlcpLineAlarmState

This variable is a bitmap of the DSX3 Line alarms. A value of zero indicates no alarms. Itemized below are the individual bits: BitPosition Alarm ----------- ----- 0 Receiving RAI 1 Transmitting RAI 2 Receiving ...

dsx3PlcpBip8CV15MinBucket

The counter associated with the number of BIP-8 code violations in the last 15 minute period encountered by the interface.

dsx3PlcpBip8CV24HrBucket

The counter associated with the number of BIP-8 code violations in the last 24 hour period encountered by the interface.

dsx3PlcpBip8ESCurrent

This counter counts the number of BIP-8 code violations Errored Seconds encountered by the interface.

dsx3PlcpBip8ES15MinBucket

This counter counts the number of BIP-8 code violations Errored Seconds in the last 15 minutes encountered by the interface.

dsx3PlcpBip8ES24HrBucket

This counter counts the number of BIP-8 code violations Errored Seconds in the last 24 hours encountered by the interface.

dsx3PlcpBip8SESCurrent

This counter counts the number of Bip8 code violations Severely Errored Seconds encountered by the interface.

dsx3PlcpBip8SES15MinBucket

This counter counts the number of BIP-8 Severely Errored Seconds in the last 15 minutes encountered by the interface.

dsx3PlcpBip8SES24HrBucket

This counter counts the number of BIP-8 Severely Errored Seconds in the last 24 hours encountered by the interface.

dsx3PlcpSEFSCurrent

This counter counts the number of Severely Errored Framing Seconds encountered by the interface.

dsx3PlcpSEFS15MinBucket

This counter counts the number of Severely Errored Framing Seconds in the last 15 minutes encountered by the interface.

dsx3PlcpSEFS24HrBucket

This counter counts the number of Severely Errored Framing Seconds in the last 24 hours encountered by the interface.

dsx3PlcpUASCurrent

This counter counts the number of Unavailable Seconds encountered by the interface.

dsx3PlcpUAS15MinBucket

This counter counts the number of Unavailable Seconds in the last 15 minutes encountered by the interface.

dsx3PlcpUAS24HrBucket

This counter counts the number of Unavailable Seconds in the last 24 hours encountered by the interface.

dsx3PlcpAlarmClrButton

This variable is used to clear all the alarms.

dsx3PlcpCounterTable

The table for DS3 PLCP counter table.

dsx3PlcpCounterEntry

An entry in the DS3 PLCP counter table.

dsx3PlcpRcvBip8Count

The number of BIP-8 errors encountered by the interface.

dsx3PlcpRcvOOFCount

The number of times the Out of Frame(OOF) was detected with or without integrating to OOF alarm.

dsx3PlcpRcvRAICount

The number of times Remote Alarm Indication(RAI) was detected with or without integrating to RAI alarm.

dsx3PlcpFECount

The number of Framing Errors detected.

dsx3PlcpFESecCount

The number of Framing Error errored seconds.

dsx3PlcpSEFESecCount

The number of Severely errored Framing error seconds.

dsx3PlcpFEBECount

The number of Far End Block Errors(FEBE) detected.

dsx3PlcpFEBESecCount

The number of FEBE errored seconds.

dsx3PlcpSEFEBESecCount

The number of Severely errored FEBE seconds.

dsx3PlcpHECCount

The number of HCS Errors.

dsx3PlcpHECSecCount

The number of HEC errored seconds.

dsx3PlcpSEHECSecCount

The number of Severely HEC error seconds.

dsx3PlcpCounterClrButton

This variable is used to clear all the counters.

dsx3PlcpCounterValidEntries

The maximum number of entries in the dsx3PlcpCounterTable.

cmDsx3GeneralGroup

The collection of objects which are used for providing number of entries in dsx3 and PLCP tables.

cmDsx3ConfGroup

The collection of objects which are used for configuring DS3/E3 interfaces.

cmDsx3E3ConfGroup

The collection of objects which are applicable for E3 interfaces only.

cmDsx3BertConfigGroup

The collection of objects which are used for BERT on DS3/E3 interfaces.

cmDsx3StatsGroup

The collection of objects related to DS3/E3 statistics.

cmDsx3E3AlarmConfGenGroup

The collection of objects used for alarm configuration of DS3 and E3 interfaces.

cmDsx3AlarmConfGroup

The collection of objects used for alarm configuration of DS3 interfaces.

cmDsx3E3AlarmConfGroup

The collection of objects used for alarm configuration of E3 interfaces.

cmDsx3AlarmStatsGenGroup

The collection of objects related to performance statistics and error events for ds3 end e3 interfaces.

cmDsx3AlarmStatsGroup

The collection of objects related to performance statistics and error events for ds3 interfaces.

cmDsx3E3AlarmStatsGroup

The collection of objects related to performance statistics and error events for e3 interfaces.

cmDsx3PlcpConfGroup

The collection of objects related to PLCP Configuration on DS3 interfaces.

cmDsx3PlcpStatsGroup

The collection of objects related to PLCP statistics on DS3 interfaces.

cmDsx3PlcpAlarmConfGroup

The collection of objects used for PLCP Alarm configuration on DS3 interfaces.

cmDsx3PlcpAlarmGroup

The collection of objects used for PLCP Alarm configuration on DS3 interfaces.