The objects described here can be monitored with the IPHost Network Monitor.
You can start SNMP monitoring using free 30-day trial version of IPHost right now.
OID list for time threshold
- Compaq Fibre Array Fibre Channel Array Physical Drive Threshold Spin up Time
- cpqFcaPhyDrvThrSpinupTime 1.3.6.1.4.1.232.16.2.6.1.1.4 (defined in CPQFCA)
Spin up Time Maximum Threshold in tenths of seconds. This shows the maximum of time it takes for a physical drive to spin up to full speed. This threshold is associated with the cpqFcaPhyDrvSpinupTime object in the Physical Drive Table. If the value cannot be determined, -1 is returned. - Compaq Fibre Array Fibre Channel Array Physical Drive Threshold Violation Spin up Time
- cpqFcaPhyDrvThrViSpinupTime 1.3.6.1.4.1.232.16.2.6.1.1.9 (defined in CPQFCA)
Spin up Time in tenths of seconds Threshold Has Been Violated. This is used to indicate whether the time it took for a physical drive to spin up to full speed has ever exceeded the maximum allowable threshold. The valid values are: false (1) Indicates that the Spin up Time object (cpqFcaPhyDrvSpinupTime) value has not exceeded the maximum threshold (cpqFcaPhyDrvThrSpinupTime). true (2) Indicates that the Spin up Time object (cpqFcaPhyDrvSpinupTime) value has exceeded the maximum threshold (cpqFcaPhyDrvThrSpinupTime). unknown (3) The agent is unable to determine if the drive has a threshold violation. - Compaq Drive Array Physical Drive Threshold Spin up Time
- cpqDaPhyDrvThrSpinupTime 1.3.6.1.4.1.232.3.2.6.1.1.11 (defined in CPQIDA)
Spin up Time Maximum Threshold in tenths of seconds. This shows the maximum of time it takes for a physical drive to spin up to full speed. This threshold is associated with the cpqDaPhyDrvSpinupTime object in the Physical Drive Table. - Compaq Drive Array Physical Drive Threshold Violation Spin up Time
- cpqDaPhyDrvThrViSpinupTime 1.3.6.1.4.1.232.3.2.6.1.1.31 (defined in CPQIDA)
Spin up Time in tenths of seconds Threshold Has Been Violated. This is used to indicate whether the time it took for a physical drive to spin up to full speed has ever exceeded the maximum allowable threshold. The valid values are: false (1) Indicates that the Spin up Time object (cpqDaPhyDrvSpinupTime) value has not exceeded the maximum threshold (cpqDaPhyDrvThrSpinupTime). true (2) Indicates that the Spin up Time object (cpqDaPhyDrvSpinupTime) value has exceeded the maximum threshold (cpqDaPhyDrvThrSpinupTime). unknown (4294967295) The agent is unable to determine if the drive has a threshold violation. - Cisco Class Based Qos RED Class Configuration Minimum Threshold Time
- cbQosREDClassCfgMinThresholdTime 1.3.6.1.4.1.9.9.166.1.11.1.1.8 (defined in CISCO-CLASS-BASED-QOS-MIB)
The minimum WRED threshold value specified in milli-seconds. The milli-second value is internally converted to bytes by using the bandwidth that is available for the class. - Cisco Class Based Qos RED Class Configuration Max Threshold Time
- cbQosREDClassCfgMaxThresholdTime 1.3.6.1.4.1.9.9.166.1.11.1.1.9 (defined in CISCO-CLASS-BASED-QOS-MIB)
The maximum WRED threshold value specified in milli-seconds. The milli-second value is internally converted to bytes by using the bandwidth that is available for the class. - Cisco Class Based Qos RED Configuration Threshold Time Group
- cbQosREDCfgThresholdTimeGroup 1.3.6.1.4.1.9.9.166.2.2.50 (defined in CISCO-CLASS-BASED-QOS-MIB)
Optional objects to provide WRED time based threshold Limit configuration information. - Cisco Content Service Net Server Response Time Fail Alarm Threshold
- ccsNetServerResponseTimeFailAlarmThreshold 1.3.6.1.4.1.9.9.597.1.1.1.1.9 (defined in CISCO-CONTENT-SERVICES-MIB)
This object specifies the alarm threshold of the number of the responses specified by ccsNetServerResponseTimeFailCountNotifInfo for the first payload packet from the network server exceeds the response time ccsNetServerFirstPayloadResponseTime within the time interval (ccsAdControlAlarmUpdateTimer). When ccsAdControlNotifEnabled is set to 'true', the count is greater than the threshold and no alarm notification specified by ciscoContentServicesNetServerResponseTimeExceeded has been issued, the alarm notification will be generated and the timer will be re-started. The threshold should be greater than the clear threshold ccsNetServerResponseTimeFailClearThreshold. When the threshold is changed, the counter will be reset, the alarm will be cleared if exists, and the timer will be re-started. - Cisco Content Service Net Server Response Time Fail Clear Threshold
- ccsNetServerResponseTimeFailClearThreshold 1.3.6.1.4.1.9.9.597.1.1.1.1.10 (defined in CISCO-CONTENT-SERVICES-MIB)
This object specifies the clear threshold associated with ccsNetServerResponseTimeFailAlarmThreshold. If ccsAdControlNotifEnabled is set to 'true', the count (ccsNetServerResponseTimeFailCountNotifInfo) is equal to or lower than the threshold when the timer (ccsAdControlAlarmUpdateTimer) expires and the alarm specified by ciscoContentServicesNetServerResponseTimeExceeded exists, the clear notification specified by ciscoContentServicesNetServerResponseTimeAlarmCleared is generated. The threshold should be less than the alarm threshold specified by ccsNetServerResponseTimeFailAlarmThreshold. When the threshold is changed, the counter will be reset, the alarm will be cleared, and the timer will be re-started. - Cisco Enhanced IP Sec Tunnel Security Association Life Time Threshold
- ceipSecTunSaLifeTimeThreshold 1.3.6.1.4.1.9.9.432.1.1.2.1.15 (defined in CISCO-ENHANCED-IPSEC-FLOW-MIB)
The security association LifeTime refresh threshold in seconds. If the tunnel was setup manually, the value of this MIB element should be 0. - Juniper Ip Sec Security Association Monitor Life Time Threshold
- jnxIpSecSaMonLifeTimeThreshold 1.3.6.1.4.1.2636.3.52.1.2.3.1.11 (defined in JUNIPER-IPSEC-FLOW-MON-MIB)
The security association LifeTime refresh threshold in seconds. - Juniper Ping Control Egress Time Threshold
- jnxPingCtlEgressTimeThreshold 1.3.6.1.4.1.2636.3.7.1.2.1.10 (defined in JUNIPER-PING-MIB)
Maximum egress trip time allowed. If this threshold is crossed by any probe, a jnxPingEgressThresholdExceeded trap will be sent. This applies only if the probe type (pingCtlType) provides one way delay measurements. Currently jnxPingIcmpTimeStamp is the only supported probe type with this property. - Juniper Ping Control Ingress Time Threshold
- jnxPingCtlIngressTimeThreshold 1.3.6.1.4.1.2636.3.7.1.2.1.13 (defined in JUNIPER-PING-MIB)
Maximum ingress trip time allowed. If this threshold is crossed by any probe, a jnxPingIngressThresholdExceeded trap will be sent. This applies only if the probe type (pingCtlType) provides one way delay measurements. Currently jnxPingIcmpTimeStamp is the only supported probe type with this property. - Switch L2 Dhcp Relay Time Threshold
- swL2DhcpRelayTimeThreshold 1.3.6.1.4.1.171.11.70.5.2.8.3 (defined in DES3528-L2MGMT-MIB)
This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet. - Switch L3 Relay Dhcp Time Threshold
- swL3RelayDhcpTimeThreshold 1.3.6.1.4.1.171.11.70.5.3.3.1.3 (defined in DES3528-SWL3MGMT-MIB)
This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet. - Switch L3 Relay Dhcp Time Threshold
- swL3RelayDhcpTimeThreshold 1.3.6.1.4.1.171.11.70.5.3.3.1.3 (defined in DES3612-SWL3MGMT-MIB)
This object indicates the minimum time in seconds within which the switch must relay the Dhcp request. If this time is exceeded, the switch will drop the Dhcp packet. - Switch L3 Relay Dhcp Time Threshold
- swL3RelayDhcpTimeThreshold 1.3.6.1.4.1.171.11.70.5.3.3.1.3 (defined in DES3650-SWL3MGMT-MIB)
This object indicates the minimum time in seconds within which the switch must relay the Dhcp request. If this time is exceeded, the switch will drop the Dhcp packet. - Switch L2 Dhcp Relay Time Threshold
- swL2DhcpRelayTimeThreshold 1.3.6.1.4.1.171.11.70.5.2.8.3 (defined in DGS3200-L2MGMT-MIB)
This object indicates the minimum time in seconds within which the switch must relay the DHCP request. If this time is exceeded, the switch will drop the DHCP packet. - Cisco IPSec Sec Tunnel Sa Life Time Threshold
- cipSecTunSaLifeTimeThreshold 1.3.6.1.4.1.9.9.171.1.3.2.1.12 (defined in CISCO-IPSEC-FLOW-MONITOR-MIB)
The security association LifeTime refresh threshold in seconds.
