CISCO-CAS-IF-EXT-MIB

CISCO-CAS-IF-EXT-MIB Download

MIBs list

The MIB module is an extension of CISCO-CAS-IF-MIB.It defines the attributes of a voice interface.

IPHost Network Monitor offer an easy way of SNMP monitoring your Cisco Servers, Routers, Switches, Bridges, Firewalls, Repeaters.

OID list for CISCO-CAS-IF-EXT-MIB

ccasIfExtVoiceCfgTable
The voice interface extended table defines the parameters related to the configuration of voice interfaces (DS0 group of DS1). This table extends the ccasVoiceCfgTable. Each table entry describes an instance of a voice interface configuration (DS0 group o ...
ccasIfExtVoiceCfgEntry
Each entry represents a voice interface (DS0 group of DS1) in a media gateway.
ccasIfExtVoiceCfgLifNumber
This object specifies the LIF (Logical InterFace) number associated with this voice interface. If this object is set to 0, this interface does not have an associated LIF.
ccasIfExtVoiceCfgCcntrlProfile
This object specifies the index of call control profile that is used by this DS0 group. If the value of ccasGrpCfgServiceType is 'mgcp(6)', this is the index of cxeCallCtrlProfileTable. If the value of ccasGrpCfgServiceType is 'h248(9)', this is the index ...
ccasIfExtVoiceCfgVadEnabled
The object specifies VAD (Voice Activity Detection) is enabled for the compression DSPs of this interface. The value of this object is 'false' if the voice interface associated DS0 group uses null signaling. (The value of ccasGrpCfgType in ccasGrpCfgTable ...
ccasIfExtVoiceCfgContinuityTone1
The object specifies the first frequency tone to be sent between the terminating and the originating gateways in the continuity test.
ccasIfExtVoiceCfgContinuityTone2
The object specifies the second frequency tone to be sent between the terminating and the originating gateways in the continuity test.
ccasIfExtVoiceCfgModemPassThru
This object specifies the modem pass-through mode: (1) passThruDisabled: Modem pass-through is disabled (2) passThruCisco: Cisco Proprietary PV (Protocol Violation) modem protocol used in modem pass-through. (3) passThruNse: Name Signaling Events( ...
ccasIfExtVoiceCfgT38MaxFaxTxRate
This object specifies the maximum FAX relay transmission rate.
ccasIfExtVoiceCfgT38HsPktPeriod
This object specifies the period of time for primary high speed (HS) data packet.
ccasIfExtVoiceCfgT38HsRedundancy
The object specifies the number of redundant FAX packets for Internet FAX protocol (IFP) packet transmission. The value of '0' indicates that no redundant Internet FAX packets will be transmitted during the T.38 FAX relay connection.
ccasIfExtVoiceCfgRepetition
This object is used to repeatedly apply the writable objects of ccasIfExtVoiceCfgTable specified in the same SNMP PDU starting from the row specifies by the index of the instance for the number of rows specified in this object. The order of operation is i ...
ccasIfExtVoiceCfgBulkCfgOwner
This object is used for error checking of the operation specified in ccasIfExtVoiceCfgRepetition. The value of this object is set by the SNMP manager with its own identifier at the same time as issuing the bulk operation by setting ccasIfExtVoiceCfgRepeti ...
ccasIfExtVoiceCfgBulkCfgResult
This object is used for error checking of the operation specified in ccasIfExtVoiceCfgRepetition. This object indicates the result of the bulk configuration initiated by the SNMP manager specified in the value of ccasIfExtVoiceCfgBulkCfgOwner.
ccasIfExtVoiceCfgVadTimer
This object specifies the hangover time for VAD. Once the voice inactivity is detected, gateway will wait for this duration before activating silence suppression.
ccasIfExtVoiceCfgICSEnable
This object specifies whether the Idle Channel suppression (ICS) is enabled for an AAL2 connection.
ccasIfExtVoiceCfgICSIntTimer
This object specifies a timeout value for ICS integration timer. This timer is started once channel idle is detected. When the timer is expired, the gateway will stop transmitting bearer data to network. Instead, the CAS keep-alive packets will be sent.
ccasIfExtVoiceCfgTonePlan
This object specifies which tone plan the DS0 group is using for playing the tones.
ccasIfExtVoiceCfgGwyLinkId
This object specifies the H.248 media gateway link that this DS0 group belongs to. This object is applicable only if the value of ccasGrpCfgServiceType is 'h248(9)'.
ccasIfExtVoiceCfgH248PkgIds
This object specifies the H.248 packages supported in this DS0 group. This object is applicable only if the value of ccasGrpCfgServiceType is 'h248(9)'.
ccasIfExtVoiceCfgEventMappingIdx
This object specifies the action of the voice band data signal events handling in this DS0 group. The real-time detected voice band data events are categorized by VoiceBandDataEventType defined in CISCO-VOICEBAND-DATA-PROFILE-MIB. The value of this object ...
ccasIfExtVoiceCfgGatewayIndex
This object specifies the media gateway index that this DS0 group belong to. The value of this object is cmgwIndex in cMediaGwTable.
ccasIfExtVoiceCfgCasProfile
This object specifies the index of CAS profile that is used by this DS0 group. The value of this object is ccasProfileIndex in ccasIfExtProfileTable. This object is applicable only when the DS0 group is in a DS1 line whose signal mode is configured for CA ...
ccasIfExtDs0GrpCfgEntry
Each entry represents a DS0 group interface.
ccasIfExtDs0GrpRepetition
This object is used to repeatedly apply the writable objects of ccasIfExtDs0GrpCfgTable specified in the same SNMP PDU starting from the row specifies by the index of the instance for the number of rows specified in this object. The repetition operation w ...
ccasIfExtDs0GrpRepeatResult
This object is used for error checking of the operation specified in ccasIfExtDs0GrpRepetition. This object indicates the result of the repetition initiated by the SNMP manager specified in the value of ccasIfExtDs0GrpRepeatOwner. ::= { ccasIfExtDs0GrpCfg ...
ccasIfExtProfileEntry
Each entry represents a CAS profile in media gateway.
ccasProfileIndex
This object uniquely identifies the CAS profile. The value of 1 specifies the default CAS profile in the media gateway.
ccasProfileLineSigTimer
This object specifies the attributes of CAS line signaling timers indicated by ccasLSTIndex in ccasIfExtLineSignalTimerTable. DEFVAL { 1 } ::= { ccasIfExtProfileEntry 2 } SYNTAX Unsigned32 (1..65535) MAX-ACCESS read-create STATUS current DESCRI ...
ccasIfExtVariantTable
This table specifies a list of CAS signaling protocols such as R2 CAS, Feature Group D Oprerator Services ( FGD OS). Each CAS variant is downloaded to and parsed by the media gateway. A CAS variant can be applied to a DS0 group of the DS1 line with CAS si ...
ccasIfExtVariantEntry
Each entry represents a CAS variant in media gateway. Upon the creation of the entry, the CAS variant specified by ccasVariantFile will be downloaded to the media gateway. After the file is successfully parsed by the media gateway, a corresponding entry i ...
ccasVariantIndex
An arbitrary value which uniquely identifies the CAS variant in the media gateway.
ccasVariantFile
This object specifies the valid file name with extension '.o' stored on the media gateway's hard disk. The CAS variant file can be transferred to the media gateway via FTP text file transfer mechanism.
ccasVariantSource
This object specifies the source from where the CAS variant file must be fetched. . internal: Value indicates that the file is built into the firmware. . external: Value indicates that the file is to be downloaded from the media gateway. DEFVAL { internal ...
ccasVariantState
This object indicates the configuration status of the CAS variant. . initInProgress: The state machine is being initialized. . initSuccessfully: The state machine was initialized properly. . initFailed: The intialization failed. ::= { ccasIfExtVariantEntr ...
ccasIfExtIncomingLineSignalTable
This table defines the parameters related to the incoming line signals for CAS variant. The appropriate signal definitions from this table will be downloaded to the media gateway. The media gateway will use the information provided in this table to match ...
ccasOLSMakeTime
This object specifies the time value for which the Tx Pattern being transmitted. ::= { ccasIfExtOutgoingLineSignalEntry 4 } SYNTAX Unsigned32 (0..4294967295) UNITS "milliseconds This object specifies the time value for which the pattern being t ...
ccasBwdRSPrevDigit
This object specifies a backward signal requesting transmission of the previous ANI or DNIS digit (n - 1) after reception of digit n. The default value is country specific. REFERENCE ITU-T Q440 - Specifications of signaling system R2 Interregister Signali ...
ccasIfExtLineSignalTimerEntry
Each entry represents a CAS Line Signal Timer in media gateway. INDEX { cmgwIndex, ccasLSTIndex } ::= { ccasIfExtLineSignalTimerTable 1 } CcasIfExtLineSignalTimerEntry::= SEQUENCE { ccasLSTIndex Unsigned32, ccasLSTIdleGuardTimer ...
ccasLSTClearFwdTimer
This object specifies the value of the timer that the GW will start at the request of the controlling application such as MGC for receipt of the clear forward signal on the line. This object is applied to R2 CAS. REFERENCE ITU-T Recommandation Q.118 Abnor ...
ccasLSTClearBwdTimer
This object specifies the value of the timer that the GW will start at the request of the controlling application such as MGC for receipt of the clear backward signal. This object is applied to R2 CAS. REFERENCE ITU-T Recommandation Q.118 Abnormal conditi ...
ccasLSTReleaseGuardTimer
This object specifies the delay between reception of the clear forward signal and the sending of the idle signal. Upon reception of the clear forward signal, GW starts the release guard timer. Upon expiry of this timer, the idle signal is generated. This ...
ccasLSTCASGlareTimer
This object specifies the maximum amount of time MG will wait for other end to back out when glare occurs on a DS0 line. Change in incoming off-hook signal to on-hook signal with-in this time frame indicates that other end has backed down. REFERENCE H248. ...
ccasLSTAnswerMeterDelayTimer
The object specifies the delay between generation of the answer signal and the generation of the meter signal. The GW will start this timer after having sent the line answer signal. DEFVAL { 600 } ::= { ccasIfExtLineSignalTimerEntry 7 } SYNTAX Unsign ...
ccasLSTDelayBetRegAnsAndLineAns
This object specifies the timer that will be started after register signaling completes successfully, within which the answer line signal should be received. This applies to outgoing R2 registers. The value of 0 indicates the timer will not be started and ...
ccasLSTRowStatus
This object is used for adding, deleting, and modifying the entries from the ccasIfExtLineSignalTimerTable. A default entry with index value 1 is created at initialization, and it cannot be modified or deleted. ::= { ccasIfExtLineSignalTimerEntry 12 } -- ...
ccasRSTCompelledFwdToneOffTimer
This object specifies the period for which the forward signal digit is turned off in compelled signaling. This timer is started after the backward signal is received and after the forward signal digit is turned off on the outgoing interface. REFERENCE ITU ...
ccasRSTCompelledBwdToneOnTimer
This object specifies the period for which the backward signal stays on waiting for the forward digit signal to go off in compelled signaling. This timer is started after the backward signal is sent in response to the forward signal digit. DEFVAL { 15 } : ...
ccasRSTIncomingRegSigDuration
This object specifies the duration within which the register signaling should complete for an incoming call. This timer is started as soon as the first forward register signal is received. DEFVAL { 180 } ::= { ccasIfExtRegSignalTimerEntry 10 } SYNTAX ...
ccasRSTRowStatus
This object is used for adding, deleting and modifying the entries from the ccasIfExtRegSignalTimerTable. A default entry with index value 1 is created at initialization, and it can not be modified or deleted. ::= { ccasIfExtRegSignalTimerEntry 13 } -- ** ...
ccasGCnfLineSigType
This object specifies the line signaling type that will be used for the R2 line signaling. . digital (1): The digital line signaling is typically used for PCM systems. Only A and B bits are used to indicate line signaling states, while C and D bits may be ...
ccasGCnfRingBackType
This object specifies the ring back signal type of FGD protocol. . wink (1): A pulse which is a timed transition from on hook to off hook and back to on hook. . wink and tone (2): A pulse which is a timed transition from on hook to off hook and back to on ...
ccasGCnfIncCallHiFreqPower
This object specifies the power of the high frequency signal component for incoming call. REFERENCE TIA-689-A: PBX and KTS Support of Enhanced 911 Emergency Calling Service, section 5.2.3.10.1 ::= { ccasIfExtGeneralConfigEntry 7 } SYNTAX Integer32 (- ...
ccasGCnfOutCallPowerTwist
This object specifies the relative power level of the high frequency component for outgoing call. When this object is set to 0, the power level of both frequency components is set to the same level. When this object is set to a positive value, the power l ...
ccasGCnfOutCadenceOntime
This object specifies the duration during which the digit tone is generated for outgoing call. ::= { ccasIfExtGeneralConfigEntry 14 } SYNTAX Unsigned32 (0..65535) UNITS "milliseconds This object specifies the silence between digit tones for out ...
ccasGCnfEchoCancellation
This object specifies the echo cancellation mode, and it is applicable to an outgoing R2 register. DEFVAL { outgoingHalfEchoRequired } ::= { ccasIfExtGeneralConfigEntry 17 } SYNTAX INTEGER{ subscriberWithoutPriority (1), subscriberWi ...
ccasGCnfDigitType
This object specifies the digit type to pulsed from the GW such as: .dtmf - Dual tone multifrequency. .mf - Multifrequency. .dp - Dial pulse. This parameter can be overridden by MGC. In the event that the MGC does not specify the digit type, the value of ...
ccasGCnfInitialDelay
This object specifies the initial delay that must be applied on an outgoing trunk before the digits are pulse out. The value of 0 indicates the timer, ccasGCnfInitialDelay will start immediately. REFERENCE H.248.25 Basis CAS Packages section 8.3.1
ccasGCnfMaxNumCallParty
This object specifies the maximum number of calling party digits to collect for reporting to the MGC. The MGC can overridden this value, and a value of 0 indicates that there is no limit and all numbers till end of calling party signaling must be accumula ...
ccasIfExtVoiceCfgGroup
This group contains objects that apply to the DS0 group of DS1 configuration in media gateways.
ccasIfExtBulkGroup
This group contains objects that apply to the bulk configuration for the DS0 group associated voice specific parameters in media gateway.
ccasIfExtVoiceCfgGroupRev1
This group contains objects that apply to the DS0 group of DS1 configuration in media gateways.
ccasIfExtVoiceCfgCasGroup
This group contains objects that apply to the DS0 group of DS1 configuration for CAS.
ccasIfExtProfileGroup
A collection of objects providing information applicable to CAS Profile.
ccasIfExtConfigLineSignalGroup
A collection of objects providing information applicable to Line Signal.
ccasIfExtConfigRegisterSignalGroup
A collection of objects providing information applicable to Register Signal.
ccasIfExtConfigTimerGroup
A collection of objects providing information applicable to timer.
ccasIfExtGeneralConfigGroup
A collection of objects providing information applicable to general CAS configuration.
ccasIfExtVoiceCfgGroupSup1
This group contains supplemental objects that apply to the voice configuration in media gateways.

Download IPHost Network Monitor (500 monitors for 30 days, 50 monitors free forever) to start monitoring network devices right now.

MIBs list