The objects described here can be monitored with the IPHost Network Monitor.
You can start SNMP monitoring using free 30-day trial version of IPHost right now.
OID list for hold time
- dot1d Stp Hold Time
- dot1dStpHoldTime 1.3.6.1.2.1.17.2.10 (defined in BRIDGE-MIB)
This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second. - v Stp Hold Time
- vStpHoldTime 1.3.6.1.4.1.800.2.2.5.14 (defined in XYLAN-VLAN-MIB)
This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this VLAN, in units of hundredths of a second. - xylan XIP GMAP hold time
- xylanXIPGMAPholdtime 1.3.6.1.4.1.800.2.20.1.4 (defined in XYLAN-XIP-MIB)
information received in GMAP update packets. - clnp Net To Media Hold Time
- clnpNetToMediaHoldTime 1.3.6.1.3.1.1.23.1.6 (defined in rfc1238)
The time in seconds this entry will be valid. Static entries should always report this field as -1. - clnp Media To Net Hold Time
- clnpMediaToNetHoldTime 1.3.6.1.3.1.1.24.1.6 (defined in rfc1238)
The time in seconds this entry will be valid. Static entries should always report this field as -1. - dot1d Stp Hold Time
- dot1dStpHoldTime 1.3.6.1.2.1.17.2.10 (defined in rfc1493)
This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second. - bgp Peer Hold Time
- bgpPeerHoldTime 1.3.6.1.2.1.15.3.1.18 (defined in rfc1657)
Time interval in seconds for the Hold Timer established with the peer. The value of this object is calculated by this BGP speaker by using the smaller of the value in bgpPeerHoldTimeConfigured and the Hold Time received in the OPEN message. This value must be at lease three seconds if it is not zero (0) in which case the Hold Timer has not been established with the peer, or, the value of bgpPeerHoldTimeConfigured is zero (0). - bgp Peer Hold Time Configured
- bgpPeerHoldTimeConfigured 1.3.6.1.2.1.15.3.1.20 (defined in rfc1657)
Time interval in seconds for the Hold Time configured for this BGP speaker with this peer. This value is placed in an OPEN message sent to this peer by this BGP speaker, and is compared with the Hold Time field in an OPEN message received from the peer when determining the Hold Time (bgpPeerHoldTime) with the peer. This value must not be less than three seconds if it is not zero (0) in which case the Hold Time is NOT to be established with the peer. The suggested value for this timer is 90 seconds. - BDG Device Hold Time
- bdgdeviceHoldTime 1.3.6.1.4.1.173.7.9.1.1.30 (defined in ctron-bdg-mib)
The minimum time period elapsing between the transmission of configuration BPDU's through a given bridge port. - Cabletron Pvst Stp Hold Time
- ctPvstStpHoldTime 1.3.6.1.4.1.52.4.1.2.3.2.2.5.1.11 (defined in ctron-bridge-mib)
This time value determines the interval length during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second. - Cabletron CDP Hold Time
- ctCDPHoldTime 1.3.6.1.4.1.52.4.1.2.19.2.5 (defined in ctron-cdp-mib)
The maximum amount of time in seconds to wait before aging out an entry in the ctCDPNeighborTable. The agent may choose to change this value based on the hold time it receives from other devices so as to have a stable neighbor table which ages out entries in accordance with the transmit frequency. - sfcs Bandwidth Port Pool Trap Management Hold Down Time
- sfcsBwPortPoolTrapMgmtHoldDownTime 1.3.6.1.4.1.52.4.1.2.11.1.1.12.3.3.1.9 (defined in ctron-sfcs-mib)
The time between traps of the same type. If a trap of a particular type is generated for a particular port, another of that type for that port will not be generated until the hold down time has expired. (If it has never been set, the value will be -1.) - xst Instance Configuration Hold Time
- xstInstanceCfgHoldTime 1.3.6.1.4.1.52.4.12.30.1.5.6.4.1.10 (defined in v2h124-24-mib)
during which no more than two Configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second. - bgp Peer Hold Time
- bgpPeerHoldTime 1.3.6.1.2.1.15.3.1.18 (defined in BGP4-MIB)
Time interval in seconds for the Hold Timer established with the peer. The value of this object is calculated by this BGP speaker by using the smaller of the value in bgpPeerHoldTimeConfigured and the Hold Time received in the OPEN message. This value must be at lease three seconds if it is not zero (0) in which case the Hold Timer has not been established with the peer, or, the value of bgpPeerHoldTimeConfigured is zero (0). - bgp Peer Hold Time Configured
- bgpPeerHoldTimeConfigured 1.3.6.1.2.1.15.3.1.20 (defined in BGP4-MIB)
Time interval in seconds for the Hold Time configured for this BGP speaker with this peer. This value is placed in an OPEN message sent to this peer by this BGP speaker, and is compared with the Hold Time field in an OPEN message received from the peer when determining the Hold Time (bgpPeerHoldTime) with the peer. This value must not be less than three seconds if it is not zero (0) in which case the Hold Time is NOT to be established with the peer. The suggested value for this timer is 90 seconds. - Cisco Network Clock Ncdp Hold Time
- cncNcdpHoldTime 1.3.6.1.4.1.9.9.121.1.1.6 (defined in CISCO-ATM-NETWORK-CLOCK-MIB)
The delay between the transmission of NCDP configuration PDUs. The hold time is used to limit the transmission of NCDP configuration PDUs out of an interface to a maximum of one configuration PDU per hold time interval per interface. The value of this object should normally be set to match the value of cncNcdpMessageInterval. If the value of this object is higher than the value of cncNcdpMessageInterval, NCDP configuration PDUs will end up being propagated at the rate specified by the value of this object instead. This object is only used by the NCDP protocol entity. - CISCO CABLE AVAILABILITY HCCP Group Hold Time
- ccaHCCPGroupHoldTime 1.3.6.1.4.1.9.9.242.1.1.2.1.5 (defined in CISCO-CABLE-AVAILABILITY-MIB)
Hold time is the interval(in milliseconds) between the time of receiving the last HELLO ACK message and the time to assume that the cable interface is out of service. In the case of Working, it is the interval in milliseconds between the time when the Working receives a HELLO message and the time to assume that Protect has failed. In the case of Protect, it is the interval in milliseconds between the time when the Protect sends last HELLO message without seeing HELLO_ACK and the time to assume that Working has failed. It is carried by HELLO message and is used by Protect and all Working. - CISCO BGP4 Peer2 Hold Time
- cbgpPeer2HoldTime 1.3.6.1.4.1.9.9.187.1.2.5.1.21 (defined in CISCO-BGP4-MIB)
Time interval (in seconds) for the Hold Timer established with the peer. The value of this object is calculated by this BGP speaker, using the smaller of the values in cbgpPeer2HoldTimeConfigured and the Hold Time received in the OPEN message. This value must be at least three seconds if it is not zero (0). If the Hold Timer has not been established with the peer this object MUST have a value of zero (0). If the cbgpPeer2HoldTimeConfigured object has a value of (0), then this object MUST have a value of (0). - CISCO BGP4 Peer2 Hold Time Configured
- cbgpPeer2HoldTimeConfigured 1.3.6.1.4.1.9.9.187.1.2.5.1.23 (defined in CISCO-BGP4-MIB)
Time interval (in seconds) for the Hold Time configured for this BGP speaker with this peer. This value is placed in an OPEN message sent to this peer by this BGP speaker, and is compared with the Hold Time field in an OPEN message received from the peer when determining the Hold Time (cbgpPeer2HoldTime) with the peer. This value must not be less than three seconds if it is not zero (0). If it is zero (0), the Hold Time is NOT to be established with the peer. The suggested value for this timer is 90 seconds. - Cisco Discovery Protocol Global Hold Time
- cdpGlobalHoldTime 1.3.6.1.4.1.9.9.23.1.3.3 (defined in CISCO-CDP-MIB)
The time for the receiving device holds CDP message. The default value is 180 seconds. - Cisco Enhanced Interior Gateway Protocol Hold Time
- cEigrpHoldTime 1.3.6.1.4.1.9.9.449.1.4.1.1.5 (defined in CISCO-EIGRP-MIB)
The count-down timer indicating how much time must pass without receiving a hello packet from this EIGRP peer before this router declares the peer down. A peer declared as down is removed from the table and is no longer visible. - Cisco Fibre Element If Hold Time
- fcIfHoldTime 1.3.6.1.4.1.9.9.289.1.1.2.1.16 (defined in CISCO-FC-FE-MIB)
The maximum time that the FC-Port shall hold a frame in the transmitter buffer before discarding it, if it is unable to deliver the frame. The value 0 in this object means the frame will be discarded immediately if the port is unable to deliver the frame. Since this is a characteristic of a physical port, this object is not applicable for Port Channel ports, i.e., the value is instantiated but its value is irrelevant. - Cisco Fibre Element If Capability Hold Time Max
- fcIfCapHoldTimeMax 1.3.6.1.4.1.9.9.289.1.1.7.1.10 (defined in CISCO-FC-FE-MIB)
The maximum holding time ( in microseconds ) that the FC-Port is capable of supporting. - Cisco Fibre Element If Capability Hold Time Minimum
- fcIfCapHoldTimeMin 1.3.6.1.4.1.9.9.289.1.1.7.1.11 (defined in CISCO-FC-FE-MIB)
The minimum holding time ( in microseconds ) that the FC-Port is capable of supporting. - Fibre Channel Management Fx Port Hold Time
- cfcmFxPortHoldTime 1.3.6.1.4.1.9.10.999999.1.7.1.4 (defined in CISCO-FC-MGMT-MIB)
The maximum time that this Fx_Port shall hold a frame before discarding the frame if it is unable to deliver the frame. The value 0 means that this Fx_Port does not support this parameter. - Fibre Channel Management Fx Port Capability Hold Time Max
- cfcmFxPortCapHoldTimeMax 1.3.6.1.4.1.9.10.999999.1.7.1.11 (defined in CISCO-FC-MGMT-MIB)
The maximum holding time that this Fx_Port is capable of supporting. - Fibre Channel Management Fx Port Capability Hold Time Minimum
- cfcmFxPortCapHoldTimeMin 1.3.6.1.4.1.9.10.999999.1.7.1.12 (defined in CISCO-FC-MGMT-MIB)
The minimum holding time that this Fx_Port is capable of supporting.
