The objects described here can be monitored with the IPHost Network Monitor.
You can start SNMP monitoring using free 30-day trial version of IPHost right now.
OID list for switch status
- access Switch System Current Status
- accessSwitchSystemCurrentStatus 1.3.6.1.4.1.890.1.5.1.1.1 (defined in ZYXEL-accessSwitch-MIB)
The sysCurrentStatus is a bit map represented as a sum, therefore, it can represent multiple defects simultaneously. The sysNoDefect should be set if and only if no other flag is set. The various bit positions are: 1 sysNoDefect 2 sysOverHeat 3 sysFanRpmLow 4 sysVoltageLow 5 sysThermalSensorFailure - access Switch Vdsl Vtuo Current Status
- accessSwitchVdslVtuoCurrStatus 1.3.6.1.4.1.890.1.5.12.1.1.1.2.1.9 (defined in ZYXEL-VDSLLINE-MIB)
Indicates mandatory state of the VTU-O line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming VTU-O failure due to not receiving valid frame. 2 lossOfSignal VTU-O failure due to not receiving signal. 3 lossOfPower VTU-O failure due to loss of power. Note: the Agent may still function. 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. 5 lossOfLink VTU-O failure due to inability to link with VTU-R. 6 dataInitFailure VTU-O failure during initialization due to bit errors corrupting startup exchange data. 7 configInitFailure VTU-O failure during initialization due to peer VTU not able to support requested configuration 8 protocolInitFailure VTU-O failure during initialization due to incompatible protocol used by the peer VTU. 9 noPeerVtuPresent VTU-O failure during initialization due to no activation sequence detected from peer VTU. This is intended to supplement ifOperStatus. - access Switch Vdsl VTU-R Current Status
- accessSwitchVdslVturCurrStatus 1.3.6.1.4.1.890.1.5.12.1.1.1.3.1.9 (defined in ZYXEL-VDSLLINE-MIB)
Indicates mandatory state of the VTU-R line. This is a bit-map of possible conditions. The various bit positions are: 0 noDefect There no defects on the line 1 lossOfFraming VTU-R failure due to not receiving valid frame. 2 lossOfSignal VTU-R failure due to not receiving signal. 3 lossOfPower VTU-R failure due to loss of power. Note: the Agent may still function. 4 lossOfSignalQuality Loss of Signal Quality is declared when the Noise Margin falls below the Minimum Noise Margin, or the bit-error-rate exceeds 10^-7. This is intended to supplement ifOperStatus. - access Switch Vdsl Line Configuration Profile Row Status
- accessSwitchVdslLineConfProfileRowStatus 1.3.6.1.4.1.890.1.5.12.1.1.1.10.1.11 (defined in ZYXEL-VDSLLINE-MIB)
This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to `active'. When `active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to `destroy' or `outOfService') it must be first unreferenced from all associated lines. If the implementator of this MIB has chosen not to implement `dynamic assignment' of profiles, this object's MIN-ACCESS is read-only and its value is always to be `active'. - Compaq Fibre Array Fibre Channel Switch Network Link Status
- cpqFcSwitchNetworkLinkStatus 1.3.6.1.4.1.232.16.4.1.1.1.11 (defined in CPQFCA)
Compaq Fibre Channel Switch Network Link Status. The following values are defined: other(1) The agent is unable to determine the status of the switch network link. active(2) The switch network link is active. notActive(3) The switch network link is not active. - Compaq Fibre Array Fibre Channel Switch Fibre Connect Status
- cpqFcSwitchFibreConnectStatus 1.3.6.1.4.1.232.16.4.1.1.1.12 (defined in CPQFCA)
Compaq Fibre Channel Switch Fibre Channel Connection Status. The following values are defined: other(1) The agent is unable to determine the status of the switch fibre channel connection. ok(2) The switch Fibre Channel connection is OK. offline(3) The switch Fibre Channel connection is offline. - els100 Switch Port Mirroring Status
- els100SwitchPortMirroringStatus 1.3.6.1.4.1.52.1011.3.7 (defined in ctels100-ng-mib)
The Port Mirroring status of the system, either disable or enable. - els100 Switch Vlan Status
- els100SwitchVlanStatus 1.3.6.1.4.1.52.1011.3.13.1.5 (defined in ctels100-ng-mib)
Control variable used to enable or disable the operation of the associated VLAN in the system. - Enterasys Extended Switch Admin Status
- etsysESwitchAdminStatus 1.3.6.1.4.1.5624.1.2.10.1.1.1 (defined in enterasys-eswitch-mib)
DURABLE: The meanings of the values are: enabled(1) - setting this object to enabled causes the device to begin it's power up sequence and attempt to enter its operational state. If the value of this object was disabled, then the non-volatile value of this object is changed to enabled. As part of the power up sequence, the device's management parameters may or may not be reset. (In other words, the device may go through the equivalent of a reset or before returning to the online state. If the device is capable of going directly from the disabled state to the enabled state without resetting any of its management parameters, then it may do so. Such action is product specific.) disabled(2) - setting this object to offline causes the device to cease network activity and enter a quiescent state. A disabled device must still be able to respond to management messages. The value enable(1) or disable(2) shall be stored in non-volatile memory for the initial reset value of this variable. The factory default NV value is enable(1). - Enterasys Extended Switch Ether Type Status
- etsysESwitchEtherTypeStatus 1.3.6.1.4.1.5624.1.2.10.1.4.1.1.3 (defined in enterasys-eswitch-mib)
This object indicates the administrative status of this entry. other(1) - This entry is currently in effect, but the conditions under which it will remain so differ from the ones described for the other enumeration values invalid(2) - Writing this value invalidates the entry. The agent may (but is not required to) delete the row. permanent(3) - This entry is currently in use and will remain so after the next reset of the bridge. deleteOnReset(4) - This entry is currently in use and will remain so until the next reset of the bridge. - Enterasys Extended Switch Protocol Status
- etsysESwitchProtocolStatus 1.3.6.1.4.1.5624.1.2.10.1.4.2.1.7 (defined in enterasys-eswitch-mib)
This object indicates the administrative status of this entry. other(1) - This entry is currently in effect, but the conditions under which it will remain so differ from the ones described for the other enumeration values invalid(2) - Writing this value to the object deletes the filter or VLAN constraint. The agent may delete the SNMP table row or return an AdminStatus of 'invalid' at its discretion. permanent(3) - This entry is currently in use and will remain so after the next reset of the bridge. deleteOnReset(4) - This entry is currently in use and will remain so until the next reset of the bridge. - Cisco ATM Switch Address Row Status
- atmSwitchAddressRowStatus 1.3.6.1.2.1.37.1.14.1.17.1.3 (defined in ATM2-MIB)
Used to create, delete, activate, and de-activate addresses used to identify this switch. - cisco Atm Switch Address Row Status
- ciscoAtmSwAddrRowStatus 1.3.6.1.4.1.9.9.51.1.1.1.3 (defined in CISCO-ATM-SWITCH-ADDR-MIB)
This object is used to create and delete rows in the ciscoAtmSwAddrTable. - Cisco ATM Switch Closed User Group Interlock Code Row Status
- csCugInterlockCodeRowStatus 1.3.6.1.4.1.9.9.89.1.1.1.3 (defined in CISCO-ATM-SWITCH-CUG-MIB)
To create, delete a row. Existing rows can be modified/deleted when the row is active providing this alias is not referenced by any entries in the csCugTable. - Cisco ATM Switch Closed User Group If Row Status
- csCugIfRowStatus 1.3.6.1.4.1.9.9.89.1.2.1.4 (defined in CISCO-ATM-SWITCH-CUG-MIB)
The status of this conceptual row. The value of the columnar objects in this row may be modified even while the row status is 'active'. - Cisco ATM Switch Closed User Group Row Status
- csCugRowStatus 1.3.6.1.4.1.9.9.89.1.3.1.5 (defined in CISCO-ATM-SWITCH-CUG-MIB)
The status of this conceptual row. The value of the columnar objects in this row may be modified even while the row status is 'active'. Modifications will affect new calls. Existing calls are not affected. - Cisco Catalyst 8540 switch Cpu Status
- ccrCpuStatus 1.3.6.1.4.1.9.9.105.1.1.1.1.3 (defined in CISCO-C8500-REDUNDANCY-MIB)
The operational status of this CPU card. - Cisco Catalyst 8540 switch Switch Status
- ccrSwitchStatus 1.3.6.1.4.1.9.9.105.1.2.1.1.3 (defined in CISCO-C8500-REDUNDANCY-MIB)
The operational status of this switch card. - Cisco Network Office Switch Port Duplex Status
- cnosPortDuplexStatus 1.3.6.1.4.1.9.10.43.1.3.1.1.4 (defined in CISCO-CNO-SWITCH-MIB)
The operating duplex mode of the switched port. - Cisco Network Office Switch Port Speed Status
- cnosPortSpeedStatus 1.3.6.1.4.1.9.10.43.1.3.1.1.6 (defined in CISCO-CNO-SWITCH-MIB)
The operating speed of the switched port. - Cisco Network Office Switch Port Link Status
- cnosPortLinkStatus 1.3.6.1.4.1.9.10.43.1.3.1.1.8 (defined in CISCO-CNO-SWITCH-MIB)
The current port link status.
